Do Silicone Candle Molds Need a Release Agent?

No. Our silicone candle molds don't need oil, spray or any other release agent when you pour pure beeswax. Silicone is naturally non-stick and flexible, so once the candle has set fully at room temperature you simply flex the mold and the candle releases.

Why don't silicone molds need a release agent?

Release agents were made for rigid molds, such as metal or plastic, where the candle has to slide out of a shape that cannot move. Silicone works differently in two ways:

  • Wax doesn't bond to it. Silicone has a smooth, non-stick surface, so set beeswax has very little to hold on to.
  • It flexes. Instead of pushing the candle out, you peel the mold away from it. Even detailed shapes and textures come free without the candle being forced.

Our molds are handmade in Latvia from high-quality Italian silicone and are made for pure beeswax. Used as described below, the candle comes out clean without anything added to the mold.

Beeswax candle freshly released from a silicone mold

Can a release agent cause problems?

Adding oil or spray to a mold that doesn't need it brings downsides and no benefit:

  • It can leave a greasy or dull film on the surface of the candle.
  • It collects in fine details and textures, softening the pattern on later candles.
  • It builds up in the mold, which then needs washing out more often.
  • It is one more product to buy and one more step that can go wrong.

How do you get a clean release every time?

  1. Start with a clean, dry mold. Wash it occasionally with soap and warm water and let it dry fully.
  2. Thread the wick through the base and centre it at the top. A wick holder or a stick laid across the top keeps it straight while the wax sets. Wick holders fit only some molds, so check the wick holder product page for compatibility.
  3. Pour beeswax at 70–75 °C (158–167 °F). Pour steadily to avoid air pockets.
  4. Let it cure at room temperature until fully set. The surface can feel firm long before the centre is hard, so give it time, especially with larger candles.
  5. Flex the silicone and release. Peel the mold back from the candle, working around it, rather than pulling the candle out by its wick.

Beeswax taper candle with its silicone mold

Our guide to using our molds shows the whole process step by step.

What if a candle doesn't come out easily?

Reaching for oil is not the fix. Check these instead:

  • Is it fully set? This is by far the most common cause. A candle that is still soft in the middle grips the mold and can bend or mark. Leave it longer at room temperature and try again.
  • Are you peeling or pulling? Flex the silicone away from the candle a little at a time. Pulling on the wick puts all the force on the wick hole and the top of the candle.
  • Is the mold clean? Old wax flakes or dust in the cavity can catch on the new candle. Wash the mold with soap and warm water and dry it.
  • Is it pure beeswax? Our molds are made for pure beeswax. Other waxes, such as soy, paraffin or blends, behave differently and are at your own risk.

Never cut or pry a candle out with a knife. It is easy to slip and nick the silicone, and small cuts tend to grow into tears.

FAQ

Do I need to oil a silicone candle mold before pouring beeswax?

No. Our molds need no oil, spray or release agent with pure beeswax. Let the candle set fully, then flex the silicone and release it.

Why is my beeswax candle hard to get out of the mold?

Usually it has not fully set yet. Leave it longer at room temperature, then peel the silicone back from the candle instead of pulling on the wick.

Should I put the mold in the fridge or freezer to speed it up?

We recommend letting the candle cure at room temperature until it is fully set. That is how our molds are meant to be used.

Can a release agent harm the candle?

It can leave a film on the candle surface and build up in the mold, which then needs washing off. With our molds and pure beeswax it is simply not needed.

Is it the same with soy or paraffin wax?

Our molds are made for pure beeswax. Other waxes such as soy or paraffin are at your own risk.

If you want to try it yourself, the Birthday candles mold and the Taper candles mold are good places to start, or browse all our silicone candle molds.

Back to blog