How to Care for Silicone Candle Molds So They Last
Share
Caring for a silicone candle mold is simple: peel out any leftover wax, wash it now and then with soap and warm water, let it dry completely and store it flat, away from heat and sunlight. Keep knives and other sharp tools away from the silicone. Looked after like this, our molds are reusable for hundreds of pours.
Why does mold care matter?
A silicone mold is a tool you will use again and again, so a few minutes of care after a pour pays back over many candles. Clean silicone gives a clean candle surface, and a mold that keeps its shape gives you candles that stand straight and burn evenly. Most damage to a mold is not wear from pouring at all. It comes from cuts, from being squashed or folded in storage, or from harsh cleaning.
Our molds are handmade in Latvia from high-quality Italian silicone and are made for pure beeswax. The routine below is all they need.
How do you clean a silicone candle mold?
- Let it cool. After releasing the candle, leave the mold until it is back at room temperature.
- Remove loose wax by hand. Flex the silicone and pick out any flakes or drips with your fingers. Beeswax comes away from silicone easily once it is cold.
- Wash occasionally with soap and warm water. You don't need to wash after every pour. When the mold looks dusty or has a film of wax, wash it in warm water with a little ordinary washing-up liquid, using your fingers or a soft cloth for the detailed areas.
- Rinse well. Make sure no soap is left in the cavity.
- Dry completely. Let it air-dry, cavity facing down, before you store it or pour again. Water left inside can spoil the surface of the next candle.

What should you never use on a silicone mold?
Silicone is tough and flexible, but it can be cut. Avoid:
- Knives, metal scrapers and skewers for digging out wax. One slip can nick the silicone, and small cuts tend to grow into tears.
- Abrasive scourers such as steel wool or the rough side of a kitchen sponge. They can scratch the inside of the mold, and every scratch shows on the candle.
- Solvents such as acetone or white spirit. Soap and warm water are enough.
- Direct flame or a heat gun aimed at the silicone to melt off wax.
If wax is really stuck in fine detail, flex the mold a few times and wash it in warm water. Patience works better than any tool.
How should you store silicone molds?
Storage is where most molds lose their shape. A few habits keep them true:
- Store them flat, or upright in their natural shape. Don't fold, roll or squash a mold to make it fit a drawer.
- Don't stack heavy items on top. Silicone slowly takes on the shape it is pressed into.
- Keep them clean and dry. Put molds away only after they have dried fully.
- Avoid sunlight and heat. A cupboard or a box at room temperature is ideal. Avoid windowsills, radiators and hot attics.
- Keep dust off. A lidded box or a bag stops dust and lint sticking to the silicone.

How do you look after the mold while pouring and releasing?
Good pouring habits protect the mold as well as the candle:
- Thread the wick gently through the base and centre it at the top. Forcing a wick through the hole is the most common way a wick hole gets stretched or torn. A wick holder keeps it centred without pulling on the silicone; wick holders fit only some molds, so check the wick holder product page for compatibility.
- Pour beeswax at 70–75 °C (158–167 °F) and pour steadily to avoid air pockets.
- Let the candle cure at room temperature until fully set.
- Flex the silicone and release the candle. Peel the mold away from the candle rather than pulling the candle out by its wick.
No oil or release agent is needed with our molds and pure beeswax, so there is no residue to clean off afterwards. Our guide to using our molds goes through the full process step by step.
How long does a silicone candle mold last?
With the care above, our molds are reusable for hundreds of pours. The signs that a mold is near the end of its life are physical damage rather than age: a cut or tear, especially around the wick hole, or a mold that no longer holds its shape. At that point it is better to replace it than to keep patching it.
Our molds are made for pure beeswax. Other waxes, such as soy or paraffin, are at your own risk.
FAQ
How do you clean a silicone candle mold?
Let it cool, peel out any loose wax with your fingers, then wash it now and then with soap and warm water. Rinse well and let it dry completely before storing it.
Can I use a knife or solvent to remove stuck wax?
No. Knives and metal tools can cut the silicone, and solvents can damage it. Warm soapy water, your fingers and a soft cloth are all you need.
How should I store silicone candle molds?
Store them clean and dry, flat or upright in their natural shape, away from direct sunlight and heat, with nothing heavy pressing on them.
How long does a silicone candle mold last?
With basic care, our molds are reusable for hundreds of pours. Replace a mold if it is cut or torn, especially around the wick hole.
Do I need to oil the mold after cleaning?
No. Our molds need no oil or release agent with pure beeswax. Just make sure the mold is completely dry before the next pour.
If you are adding to your collection, the Spiral pillar mold and the Pillars mold are easy shapes to look after, and you can browse all our silicone candle molds, shipped worldwide from Latvia.